logo
  • English Version
    • About Me
    • DG8DP
    • Technics
    • DP-AMP HVF-1k2 Amplifier
      • DP-AMP HVF-1k2 Module
        • Measurements HVF-1k2
      • DP-AMP LPF-1k2 Module
        • Measurements LPF-1k2
      • DP-AMP ATU-1k2 Module
      • DP-AMP HVF-1k2 Controller
        • GUI Concept 2022
    • DP-AMP HF-1200 Amplifire
      • The Project
      • Power supply
      • MOSFET VRF2933
      • PA Module
      • Low-Pass Filter
      • Display & Control
      • Enclosure
      • Features
      • Specifications
    • DP-HDTRX / SDR Standalone
      • DP-HDTRX Hermes
      • DP-HDTRX Mechanics
      • DP-HDTRX PC-Deck
      • DP-HDTRX HF-Deck
    • Presentations
    • Green House & IOT
    • BMW Z4
    • VIP Radio Amateurs
  • Home
  • Über mich
  • DG8DP
  • Technik
  • DP-AMP HVF-1k2 Endstufe
    • DP-AMP HVF-1k2 Modul
      • Messungen HVF-1k2
    • DP-AMP LPF-1k2 Modul
      • Messungen LPF-1k2
    • DP-AMP ATU-1k2 Modul
    • DP-AMP HVF-1k2 Controller
      • GUI Konzept 2022
  • DP-AMP HF-1200 Endstufe
    • Projekt Beschreibung
    • Netzteil
    • MOSFET VRF2933
    • PA Modul
    • Low-Pass Filter
    • Display & Bedienung
    • Gehäuse
    • Ausstattung
    • Technische Daten
  • DP-HDTRX / SDR Standalone
    • DP-HDTRX Hermes
    • DP-HDTRX PC-Deck
    • DP-HDTRX HF-Deck
    • DP-HDTRX Mechanik
  • Vorträge
  • Mein OV C01
    • Sommerfest 2024
  • Green House & IOT
  • BMW Z4
  • VIP Funkamateure

DP-AMP HVF-1k2 Amplifier

DP-AMP HVF-1k2 Amplifire

With pleasure I would like to introduce here my newest power amplifier, the HVF-1k2.

After the HF-1200 ran very well and my fingers itched again, the further development of 4x VRF2933 to 1x NXP BLF188XR began. So with the smaller PA module and new smaller power supplies I started to build a new power amp. The PA module, LPF module,
ATU module and the controller were redesigned and the switchless control concept was kept.

The housing is made of aluminum, ground and anodized black.

LAN / WLAN /USB, 2 antenna ports and a measurement output, that's all you need.

Interior view, the antenna tuner can be mounted above the filter board.

Raw...

Technical data:

Frequency range 1,8 MHz - 70 MHz
Power typ. 1 kW PEP
IMD3 typ. -35 dB twotone / -41 dB PEP
Harmonic suppression typ. 50dB
Antenna Tuner range  16:1
Power Supply internal 53 V / 57 A
Display 7" Touchscreen
Network LAN / WLAN
Filter selection manuell oder CAT
Remote Control Panel Remote Tablet, PC, MAC, Phone
Dimensions mm (WHD) 300 x 190 x 410

.


With its small dimensions, the HVF-1k2 PA is suitable for desktop use.

Two whisper-quiet fans provide sufficient ventilation, which ensures that the power amplifier stays cool and no accumulated heat is generated. Thanks to the large display, a lot of information can be shown at the same time without appearing overloaded.

Remote operation is no problem thanks to the computer used, just like a remote control unit. A tablet on the desk, the power amplifier where it is better kept, is a nice idea.
is a nice idea.

Measuring, controlling and regulating is done by an Arduino, which is programmed in C/C++. C/C++ programming is ideal for programming close to the hardware and achieving high speeds. So it is no wonder that the measured values are recorded and controlled approx. 800x per second.

The data for operation is transferred to a Raspberry PI, which handles further processing and provides the GUI for operation.

The built-in LPF board provides a very good suppression of harmonics with > 50 dB and with an IMD3 of over -41 dB PEP you still achieve an amazingly clean signal on all bands at 850 W.

If the antenna does not quite fit, the built-in antenna tuner can produce an adjustment
of up to 16:1.

DG8DP - Christian Dindas - Stand 12/2024

Datenschutz
Impressum