logo
  • English Version
    • About Me
    • DG8DP
    • Technics
    • DP-AMP HVF-1k2 Amplifier
      • DP-AMP HVF-1k2 Module
        • Measurements HVF-1k2
      • DP-AMP LPF-1k2 Module
        • Measurements LPF-1k2
      • DP-AMP ATU-1k2 Module
      • DP-AMP HVF-1k2 Controller
        • GUI Concept 2022
    • DP-AMP HF-1200 Amplifire
      • The Project
      • Power supply
      • MOSFET VRF2933
      • PA Module
      • Low-Pass Filter
      • Display & Control
      • Enclosure
      • Features
      • Specifications
    • DP-HDTRX / SDR Standalone
      • DP-HDTRX Hermes
      • DP-HDTRX Mechanics
      • DP-HDTRX PC-Deck
      • DP-HDTRX HF-Deck
    • Presentations
    • Green House & IOT
    • BMW Z4
    • VIP Radio Amateurs
  • Home
  • Über mich
  • DG8DP
  • Technik
  • DP-AMP HVF-1k2 Endstufe
    • DP-AMP HVF-1k2 Modul
      • Messungen HVF-1k2
    • DP-AMP LPF-1k2 Modul
      • Messungen LPF-1k2
    • DP-AMP ATU-1k2 Modul
    • DP-AMP HVF-1k2 Controller
      • GUI Konzept 2022
  • DP-AMP HF-1200 Endstufe
    • Projekt Beschreibung
    • Netzteil
    • MOSFET VRF2933
    • PA Modul
    • Low-Pass Filter
    • Display & Bedienung
    • Gehäuse
    • Ausstattung
    • Technische Daten
  • DP-HDTRX / SDR Standalone
    • DP-HDTRX Hermes
    • DP-HDTRX PC-Deck
    • DP-HDTRX HF-Deck
    • DP-HDTRX Mechanik
  • Vorträge
  • Mein OV C01
    • Sommerfest 2024
  • Green House & IOT
  • BMW Z4
  • VIP Funkamateure

DP-AMP HVF-1k2 Module

The PA module HVF-1k2 is a modern and powerful power amplifier module.
A lot of emphasis was put on high quality and comprehensible measured values.

The HVF-1k2 has in the input the possibility of an optional 15dB attenuator for transceivers of the 100W class to equip, so the input is insensitive to so-called power peaks.
As additional protection TVS diodes (suppressor diodes) were inserted before the 4:1 transformer, these protected the sensitive gates additionally against too high input power.

Optionally, a pre-emphasis is possible. For this purpose, the input path can be adjusted by means of a small inductance so that the low bands are somewhat attenuated and the gain is adjusted somewhat more evenly to all bands.

In order to be able to determine the temperature as well as possible, a digital temperature sensor is installed next to the BLF188XR, a DS18B20, which provides the measured temperature at the connector strip via a one-wire bus.

The operating point stabilization for AB operation was realized classically with a stabilized control loop, which has already proven itself in the HF-1200.

The BIAS voltage can be switched at the connector strip for sending. The NTC for temperature compensation is connected there and the BIAS voltage can be controlled there.

All materials used are carefully selected, Class 1 capacitors in C0G Low ESR and with the necessary current & voltage stability, real 18 Ohm cable for the TLT balun and high quality Teflon coaxial cable for the 1:1 balun in the output.

The board is made in Germany and consists of 135μm copper plating.

Technical data:

Frequency range 1,8 MHz - 70 MHz
Power typ. 1000W+ CW
IMD3 typ. 36 dBc
Operating voltage 40 VDC - 55 VDC
Current consumption max. 35 A
Input power 500 mW - 100 W
Input attenuator 3 dB - 15 dB optional
Input protection TVS-Diods
Preemphasis Optional
Temperature measurement digital One Wire
   

DG8DP - Christian Dindas - Stand 12/2024

Datenschutz
Impressum